14
preparation.
If the coee comes out too slowly or
does not come out at all, a message will
be shown GROUND TOO FINE. ADJUST
GRIND LEVEL, turn the coee mill dial
one or two clicks clockwise.
For fuller bodied creamier coee, turn one
click anticlockwise towards 1 (do not turn
more than one click at a time otherwise
the coee could come out one drop a drop
at a time).
The eect of these adjustments will only be evident after at least
2 cups of coee have been delivered. If this adjustment does not
obtain the desired result, repeat the correction by turning the
dial another click.
Tips for a hotter coee
For hotter coee, it is recommended to:
• carry out a rinse cycle by selecting the "Rinsing" function in
the settings menu (paragraph “Rinsing ”);
• warm the cups with hot water (using the hot water func-
tion, see section “hot water supply”);
• increase the coee temperature in the settings menu (see
section “Coee temperature ”).
MAKING MILKBASED HOT DRINKS
(see recipes on page 30)
Please note:
To avoid milk with little froth or large bubbles, always clean the
milk container lid (D2) and hot water connection nozzle (A9)
as described in sections “Cleaning the milk container after use”
, “Cleaning the milk container” and “Cleaning the hot water/
steam connection nozzle”.
Filling and attaching the milk container
1. Remove the lid (D2) (g.15);
2. Fill the milk container (D3) with a sucient quantity of
milk, not exceeding the MAX level marked on the contain-
er (g.16). Each mark on the side of the container corre-
sponds to about 100 ml of milk;
Please note:
• For a denser and more even froth, you must use skimmed or
partially skimmed milk at refrigerator temperature (about
5°C).
• If "Energy Saving" mode is enabled, there may be a few
seconds delay before the beverage is delivered.
1. Make sure the milk intake tube (D4) is correctly inserted in
the bottom of the milk container lid (g.17);
2. Place the lid back on the milk container;
3. Remove the hot water/steam spout (C6) (g.18);
4. By pushing the bottom attach the milk container (D) to the
nozzle (A10) (g.19): the machine will let out a noise signal
(if the sound notication function is enabled);
5. Place a suciently large cup under the coee spouts (A13)
and frothed milk spout (D5); adjust the length of the milk
spout, to move it nearer to the cup, simply pulling it down-
wards (g.20).
5. Follow the instructions below for each function.
Adjusting the amount of froth
Turn the froth adjustment dial (D1) on the milk container lid, to
adjust the amount of froth on the milk delivered while making
the drinks. Follow the tips in the table below:
Dial position Description Recommended for...
No froth CAFFE LATTE /
MILK (hot milk)
Min. froth
LATTE MACCHIATO
Max. froth CAPPUCCINO /
MILK frothed milk
Making milk-based drinks automatically
1. Fill the milk container (D) and attach it as described above.
2. Select the required beverage from the homepage:
• CAPPUCCINO
• LATTE MACCHIATO
• CAFFE LATTE
• HOT MILK
• CAPPUCCINO+
• ESPRESSO MACCHIATO
• FLAT WHITE
• CAPPUCCINO MIX
3. On the display (B) the machine recommends turning the
foam adjustment dial (D1) based on the foam requirements
for the original recipe: therefore turn the dial on top of the
milk container lid (D2) and conrm the selection by press-
ing .
4. After a few seconds, preparation begins automatically and
an image of the selected beverage appears on the display,
together with a progress bar which gradually lls as prepa-
ration progresses.