Instrukcja Obsługi Ge System Bezpieczeństwa Domowego 4 Series [9/72 Strony]

Spis treści

Rozwiń wszystko

Commands at a Glance
Concord 4 Series Security Systems
- user guide
  - Contents
- Getting to Know Your Security System
- Communicating with the System
- Basic System Operations
  - What Happens in an Alarm Condition
Note Your system may or may not be monitored. If it is not monitored, no central station reports will be made.
- Fire Alarms
  - Automatic and Manual Fire Alarms
  - Clearing Alarms and Resetting Smoke Detectors
    - 1. Press 1 + CODE. Touchpads display the zone(s) that caused the alarm (alarm memory). If sirens were still active, they will stop. The light on the smoke detector remains lit until it is reset.
    - 2. Press 1 + CODE again to reset hardwired detectors and clear alarm memory.
- Preventing Accidental Alarms
  - Guidelines for Preventing Accidental Alarms
  - Aborting Accidental Alarms
    - 1. Press 1. Touchpads display “ENTER CODE.”
    - 2. Enter your Access Code.
Note Programmed Idle Text is programmed by your installer and typically identifies the property. For example, “ABC Bank” or “The Jones’”.
- Arming and Disarming Your System
  - Level 1-OFF
Note Entry beeps are silenced after the first keypress. They will restart after five seconds with no keypresses. You must enter your access code to completely disarm the system.
- 1. Press 1. Touchpads display “ENTER CODE.”
- 2. Enter your Access Code. Touchpads display date and time or programmed text and the system sounds one long beep.
- Level 2-STAY
  - 1. Close all protected perimeter doors and windows.
  - 2. Press 2 at any touchpad. Touchpads display, “ENTER CODE.”
Note If Quick Arm feature is on, an access code is not required to arm the system to Level 2- STAY.
- 3. Enter your Access Code. Touchpads display, “Armed to STAY” and the system sounds two short beeps.
- 4. If leaving the premises, exit through a designated delay door immediately.
- Level 3-AWAY
  - 1. Close all perimeter doors and windows.
  - 2. Press 3 at any touchpad. Touchpads display, “ENTER CODE.”
Note If Quick Arm feature is on, an access code is not required to arm the system to Level 3- AWAY.
- 3. Enter your Access Code. Touchpads display, “ARMED TO AWAY” and the system sounds three short beeps.
- 4. Exit through a designated delay door immediately.
- Quick Arm
Note Contact your installer if you want to use this feature.
- Quick Exit
Important ! If you step outside and are planning to come back in, do not close the door behind you!
- 1. When the system is armed to 2-STAY, Press D at any touchpad (opening the door without pressing D will cause an alarm).
- 2. Open a designated delay door and go outside. Leave the door open if you are planning to come back in!
- 3. Return within two minutes and close the door. The system will rearm to 2-STAY.
- Keychain Touchpad Arming
- Using the Chime Feature
  - 1. While in Level 1-OFF, from any touchpad, Press 7 + 1. While the Chime feature is on, touchpads display, “CHIME IS ON” or “CHIME ON.”
  - Chime-On-Close
- Using the Voice Chime Feature
- No Delay-For Instant Alarm
Note If Quick Arm feature is on, an access code is not required. See the “Quick Arm” section in this manual.
- 1. Close all perimeter doors and windows.
- 2. Enter 2 + CODE or 3 + CODE. The system sounds two or three short beeps.
- 3. Immediately press 4. Touchpads display, “ARMED TO STAY NO DELAY” or “ARMED TO AWAY NO DELAY”.
- Auto STAY Arming Feature
- Exit Extension Arming Feature
- Arming Your System Silently
Note If Quick Arm feature is on, an access code is not required. See “Quick Arm” for more information.
Note Exit Delay is doubled when arming silently.
- 1. From any touchpad, press 5.
- 2. Within 4 seconds enter: 2 + CODE or 3 + CODE.
- Bypassing-Arming With a Door or Window Open
Note Smoke/heat sensors cannot be bypassed.
Note When a sensor is bypassed, you are allowing that door or window to be unprotected.
- Bypassing a Sensor Directly
Note You cannot bypass sensors directly using a keychain touchpad.
- 1. Close all doors and windows.
- 2. Arm your system to the desired level.
- 3. At any touchpad, press # + CODE (# is labeled Bypass)
- 4. Touchpads display, “BYPASS SENSOR _ _,” or “ENTER SNSR _ _.” Enter the desired sensor number.
- 5. Touchpads display, “BYPASSED ZONES 01,” or “SENSOR 01 BYPASSED,” for example.
- 6. If the touchpad displays “INVALID,” or “FAILURE,” or if the touchpad sounds one long beep, make sure that you entered a valid sensor number. Smoke/heat sensors cannot be bypassed.
- 7. Bypass other sensors if desired, by repeating Step 3.
- 8. The bypassed doors or windows can now be opened.
- 1. Repeat the above procedure substituting the bypassed sensor number or,
- 2. Close bypassed doors and/or windows and arm your system again.
- Bypassing a Sensor Indirectly
- Was the Bypass Successful?
  - 1. Press the Status button on the touchpad. (* is labeled Status.)
- Basic Light Control
  - 1. From any touchpad: Press 0 + 0. From a 4-button keychain touchpad: Press the Lights button.
Note For system lights to respond to basic and advanced light commands, the light switches must be turned on.
- 1. From any touchpad: Press 0 + light number. From a 4-button keychain touchpad:
- Basic Output Control
- Checking the Status of Your System
  - Short System Status
  - Full System Status
    - 1. Press * + *.
- Panic Alarms
  - Fire Panic Alarm
    - Lighting During a Fire Panic Alarm
  - Police Panic Alarm
Note Verify with your installer how your keychain touchpads are programmed. See “Appendix A: Keychain Touchpads” for more information.
- Lighting During a Police Panic Alarm
- Auxiliary Panic Alarm
  - Lighting During an Auxiliary Panic Alarm
- Siren Time-out
- Access Codes
  - Programming Access Codes
  - Changing or Erasing User Codes
    - Changing a User Code
Note The system will not accept the same code for two different users. To change System and Partition Master codes please see Appendix C: “Using Programming Menus”.
- 1. Enter the programming menus by pressing 9 + System or Partition Master CODE.
- 2. For Concord 4 systems, press 030 nnn 0 where nnn is the user 000 through 229. For Concord Express V4 systems, press 030 nn 0 where nn is the user 00 through 15.
- 3. Enter the desired 4-digit code, then #.
- 4. Press * + 00 + # to exit the programming menus.
- Deleting a User Code
- Assigning Code Attributes
- Setting the Time and Date
- Adjusting System Sounds and Touchpad Brightness
- Using the Energy Saver Feature
  - Energy Saver Example
    - Setting the Energy Saver High and Low Temperature Settings
Note Disarming the system turns off the Energy Saver.
- 1. Press 7 + 2. Alphanumeric touchpads display, “ENERGY SAVER IS ON,” for example.
- Notification by Pager
- Creating Time Schedules
- Advanced Light Control
  - Controlling Lights By Time Schedule
  - Controlling Lights with Sensors
Note If a light is attached to a sensor and a schedule, the light will only turn on and off within the scheduled start and stop times.
- 1. At an alphanumeric or fixed display touchpad, enter the programming menus by pressing 9 + System or Partition Master CODE.
- 2. Press 080. The touchpad displays “LIGHT n TO Sn x” or “LT n SN x,” (where n is the light number and x is the sensor number).
- 3. Press A or B until the light number (1-9) you would like to activate appears.
- 4. Enter the sensor number (1-96 for Concord 4, 1-32 for Concord Express V4) you wish to activate the light and press #.
- 5. Press B to assign another light to a sensor or press * + 00 + # to exit the programming menus.
- 1. At an alphanumeric or fixed display touchpad, enter the programming menus by pressing 9 + System or Partition Master CODE.
- 2. Press B until the touchpad displays “ATTACH LIGHTS TO SENSORS” or “LITE TO SN” then press #.
- 3. The touchpad displays “LIGHT n TO Sn x” or “LT n SN x,” (where n is the light number and x is the sensor number).
- 4. Press A or B until the light number (1-9) you would like to deactivate appears.
- 5. Enter the sensor number as 0 (no sensor) and press #.
- 6. Press * + 00 + # to exit the programming menus.
- Installer Programmable Lighting
- Controlling Outputs by Time Schedule
- Scheduled Arming
Note Schedules cannot be used to disarm the system.
- 1. At an alphanumeric or fixed display touchpad, enter the programming menus by pressing 9 + System or Partition Master CODE.
- 2. Press 0660 + #.
- 3. The touchpad displays “AWAY.”
- 4. Press #. The touchpad displays the first available time schedule as “SCHEDULE 00 OFF,” or “SCH 00 OFF.”
- 5. Enter
- 6. Press B to go to the next time schedule, if needed, and turn the schedule on or off for arming to AWAY.
- 7. When you’ve finished attaching the desired time schedules, press * + 00 + # to exit the programming menus.
- Opening and Closing Reports
- Latchkey Paging
Note 6 must be pressed within 5 seconds of arming. If Quick Arm feature is on, an access code is not required. See “Quick Arm” for more information.
- Notify by Exception
- The No Activity Feature
- Using the Panel Download Feature
Note Before allowing any download sessions, the system must be disarmed to level 1-OFF.
- 1. Enter the programming menus by pressing 9 + System or Partition Master CODE.
- 2. Press 041.
- 3. To turn Downloading:
- 4. Press * + 00 + # to exit the programming menus.
- Using a Partitioned System (Concord 4 systems only)
Note If your system uses just one partition, skip this section.
- 1. From any hardwired touchpad, press 8 + CODE + 6.
- 2. Press the desired partition number (1 - 6).
- 3. Proceed to arm, disarm, or program as needed. The partition assignment reverts back if no touchpad buttons are pressed for 10 seconds.
- 1. From any hardwired touchpad, press 7 + 4.
- 2. Press the desired partition number (1 - 6).
- 3. Proceed to arm, disarm, or program as needed. The partition assignment reverts back if no touchpad buttons are pressed for 10 seconds.
- Arming and Disarming Another Partition
- Programming Another Partition
- Arming and Disarming Multiple Partitions at the Same Time
Note Check with your installer to identify which keychain touchpads can arm/disarm multiple partitions.
- 1. Press 2 or 3 on any touchpad assigned to one of the partitions you want to arm. The display shows “ENTER CODE”.
- 2. Enter your Access Code. The display shows all the partitions that will be armed.
- 3. Press # to arm all displayed partitions. Or, Press the number of any partitions you don’t want armed (the partition numbers disappear from the display), then press #.
- 1. Press 1 on any touchpad assigned to the partitions you want to arm. The display shows “ENTER CODE”.
- 2. Enter your Access Code. The display shows all the partitions that will be disarmed.
- 3. Press # to disarm all displayed partitions. Or, Press the number of any partitions you don’t want disarmed (the partition numbers disappear from the display), then press #.
- 4. If desired, press 4 (No Delay) or 6 (Latchkey) to activate those features.
- Notes on Arming/Disarming Multiple Partitions from Alphanumeric and Fixed Display Touchpads
- Notes on Arming/Disarming Multiple Partitions from Keychain Touchpads
- Macro Keys
Note Macro Keys should not be programmed to disarm the system.
- System Information
- Viewing the Event Buffer
  - Overview
Note Fixed Display Touchpads cannot be used to view the event history.
- 1. The current partition must be armed to level 1 or 2.
- 2. At an alphanumeric touchpad, press 8 + System or Partition Master CODE + 8.
- Using a Touchtone Phone to Operate Your System
- Testing the System
  - Automatic Test Features
  - Manual Tests
    - Sensor Test
Important ! Do not attempt to test sensors by tripping them while the system is armed. This can result in authorities being dispatched to the site, which could result in a fine.
- 1. Make sure the system is disarmed to Level 1-Off. The system will not let you enter sensor test mode unless it is disarmed.
- 2. Press 8 + CODE + 3.
- 3. Follow the test procedure for each device as listed in the following table.
  - 4. Disarm to Level 1-Off to exit Test Mode.
- Phone Communication Test
- Testing Sirens
Important ! You must contact the central monitoring station before activating any alarms. Otherwise, authorities will be dispatched to the site which could result in a fine.
- 1. Contact the central monitoring station to inform them that you will be activating alarms and they should not dispatch authorities.
- 2. Activate alarms of each type (fire, police, auxiliary), one at a time.
- 3. Listen for the appropriate siren sound when each alarm is activated (see the “Alarm Sounds and Status Beeps” table on page 50).
- 4. Contact the central monitoring station to inform them when you are finished activating alarms.
- Troubleshooting
  - Trouble Beeps and Trouble Messages
    - Silencing Trouble Beeps
      - 1. Perform a system status check by pressing * on a touchpad,
      - 2. Change the arming level.
  - Common Questions and Answers
    - Phone Issues
    - Lighting Issues
- Appendix A: User Sheets
  - System Sensors
Note If you have more System Sensors than will fit on this sheet, make copies of this sheet and keep all the information together.
- User Codes
Note If you have more User Codes than will fit on this sheet, make copies of this sheet and keep all the information together.
- Touchpad Information
  - Alphanumeric and Fixed Display Touchpads
Note Protest beeps will always sound when bypassing.
- Keychain Touchpads
- Accidental Smoke and Fire Alarms
  - 1. Press CODE or 1 + CODE, once to silence the alarm.
  - 2. Press 1 + CODE, again to reset the smoke alarm.
- Dialer Abort
- Doors and Delay Time Settings
- System Features
- If the Power Goes Out
- No Activity Time
- Resetting the Smoke Detector
- System Information
- Paging
- Lights
- Outputs
- Energy Saver
- Alarm Sounds and Status Beeps
- Appendix B: Planning for Emergencies
Note Although having an alarm system can make you eligible for reduced insurance premiums, the system is no substitute for insurance.
- If Your System Needs Service
- Appendix C: Programming Your System
  - Two Methods to Program Your System
  - Using Programming Menus
    - Figure 14. Navigating Menus on Your Touchpad
    - Examples of Programming Using Menus
Note Step 10 can only be performed on Concord 4 systems using the System Master Code.
- 10. Press B. “PARTITION ASSIGN” or “P” appears:
- 11. Press * + B to move to the next user code, or * + 00 + # to exit the programming menus.
Note The system will not accept the same code for two different users.
- 1. Enter the programming menus by pressing 9 + System or Partition Master CODE.
- 2. Press B until the touchpad displays “USER CODES,” then press #.
- 3. The touchpad displays “REGULAR USER CODES” or “REG CODES.” Press #. (You cannot delete the System Master code.)
- 4. Press B until the touchpad displays the user code you wish to erase, then press #. For example, if you want to change User code 4, press # when the touchpad displays “USER 04” or “REG CODE 04.”
- 5. Enter the System or Partition Master code you used in Step 1 and press #. The deleted code appears as “USER 04 ****” or “RG 01 ----,” for example.
- 6. Press * + B to move to the next user code, or * + 00 + # to exit the programming menus.
- 1. Enter the programming menus by pressing 9 + System or Partition Master CODE.
- 2. Press B until the touchpad displays “USER CODES,” then press #.
- 3. The touchpad displays “REGULAR USER CODES” or “REG CODES.” Press B until the display reads “PARTITION MASTER CODE” or “PTN MASTER,” then press #.
- 4. Enter the System Master Code to delete the existing Partition Master Code OR enter a new 4 digit Partition Master Code to replace the existing code, then press #.
- 5. Press * + 00 + # to exit the programming menus.
- 1. Enter the programming menus by pressing 9 + System Master CODE.
- 2. Press B until the touchpad displays “USER CODES,” then press #.
- 3. The touchpad displays “REGULAR USER CODES” or “REG CODES.” Press B until the display reads “SYSTEM MASTER CODE” or “SYS MASTER,” then press #.
- 4. Replace the existing code with the new 4 digit System Master Code then press #.
- 5. Press * + 00 + # to exit the programming menus.
- Using Programming Shortcuts
  - 1. Enter User Programming.
  - 2. Enter a programming command sequence.

podrecznikiocean.pl

Informacje

Ge system bezpieczeństwa domowego 45136

Ge system bezpieczeństwa domowego 1000

Ge system bezpieczeństwa domowego 45130

Ge system bezpieczeństwa domowego 45129

Ge system bezpieczeństwa domowego FTP-1000

Ge system bezpieczeństwa domowego 60-875

Ge system bezpieczeństwa domowego 45137

Ge system bezpieczeństwa domowego 60-639-95R

Ge system bezpieczeństwa domowego 45227-1

Ge system bezpieczeństwa domowego XT

Ge system bezpieczeństwa domowego NX-116E

Ge system bezpieczeństwa domowego 60-639-43-EUR-OD

Ge system bezpieczeństwa domowego Simon Security System

Ge system bezpieczeństwa domowego NX-108/116/124E

Ge system bezpieczeństwa domowego 60-639-95R-OD

podrecznikiocean.pl

Informacje